Patient H is a young man with no medical concerns. At a routine examination, H complains about a nagging dull pain coming from the lower right. He reports that he often gets meat stuck there and has to “really dig” to get it out. Exam revealed an open contact between lower right first molar and lower right second bicuspid, with food impaction and tissue swelling. Radiograph taken showed localized bone loss in same area, caused by H’s inability to remove all plaque despite his eff orts. H says that, lately, he has even avoided going out for dinner with clients as he is embarrassed by this issue and finds himself trying to “pick it out” in front of his clients.
Food impaction is a common complaint and many people are not aware of the consequences of leaving this problem untreated. Food impaction can result in bone loss, periodontal pockets, inflammation, pain, decay, and is a frequent source of irritation for many patients. One of the most obvious tests that we, as dentists, can do to quickly assess these areas is to check the contact in the area that the patient complains about. Here is what to look for:
There is an additional step that we, as dentists, need to take in order to not only ensure our patient’s best oral health, but to also pro-actively diagnose additional areas where a problem is occurring or beginning to develop. In a case where a patient already complains of a food trap, I will go through the steps above in order to assess and determine the size of the food trap as well as all the consequences resulting from it. I will discuss not only the current issues including discomfort, tissue swelling, decay possibility, irritation, bone loss, I will also go over the long-term consequences of not treating it. Once the patient understands the urgency and need for treatment (steps outlined below), I then proceed to examine the remaining radiographs in order to look for additional areas that may be present. Here are the key elements to look for:
All of the above findings can contribute to food impaction and, if found, patient should be questioned thoroughly to assess if they have noticed food gathering in those areas as well. Many times, when I ask the patient, “Do you get food getting stuck between these teeth?” and point to areas where any of the above are diagnosed, the patient very often responds: “Yes! I do! How did you know?” That allows for a more thorough discussion regarding closing all contacts and restoring all problem areas at once rather than waiting until bigger issues develop. Most patients find the food impaction a nuisance and many complain about the discomfort associated with it and, as a result, they are very motivated to restore all the areas diagnosed.
The results of closing the contacts and restoring any chipping, flash, or poorly-contoured areas are instant and rewarding. As soon as the areas are restored, the patient no longer suffers from food impaction and its related irritation, and can feel instant relief from the treatment delivered. Here is the exact step-by-step process to close contacts and get rid of food traps quickly and easily:
Step 1: Place Rubber Dam with clamp and secure against leakage (see Figure 5). **For those who like to fustigate and find flaws, please note that I am very well aware of the open gap along the canine, which was well monitored throughout the entire procedure and no leakage occurred.
Step 2: Prepare teeth for restoration.
Step 3: Place matrix of appropriate size (Figure 6), and slide wedge of appropriate size to secure the band in place (Figure 7). You may need to use your finger to hold the band in place while placing the wedge.
Step 4: Place selected Garrison ® ring with forceps and ensure full seat (see Figure 8). See below for a short discussion of Garrison ® rings. The ring is placed with the loop of the ring toward or away from the forceps (depending on how the clinician chooses to restore), gripping it in the notch of the forceps and squeezing the forceps to open the ring slightly in order to place where needed down over the wedge. Once seated, the ring squeezes the teeth gently, causing slight separation so that the restorative material can then be placed in the correct contour and three-dimensional place in order to ensure a tight, positive contact with the adjacent tooth.
Step 5: Follow your adhesive protocols and, if using a flowable restorative material, place it where needed and light-cure (Figure 9). Composite resin is then added in the proximal area first and light cured. Once the proximal contact is created, additional composite is then added in order to finish the restoration.
If restoring a number of teeth at the same time, multiple rings can be used for efficiency and speed. See below for more information.
Step 6: Once cured, the ring, band, and wedge can be removed (Figure 10). Note that very little flash or excess resin remains with proper band and ring placement and the restoration can be polished quickly. The proximal contact is then checked and confirmed resulting in elimination of the food trap, and its related consequences.
The system used here to achieve solid, well-contoured, positive proximal contacts is the Strata-G™ Sectional Matrix System from Garrison® Dental (see Figure 11). This kit has definitely been designed for the busy clinician and for the anxious patient who benefits from many of the features that allow speed, efficiency, and exceptional quality and contour in the final restorations. The kit comes with a variety of bands, wedges, rings, polishers, and the Garrison® ring placement forceps. There are a number of unique features to note in this kit, which is why I choose it for my composite restorations routinely.
The bands (matrices) come in not only a variety of sizes, including a new pedodontics size, but also in soft and firm versions. These bands have a built-in enhanced marginal ridge to help the clinician shape it effortlessly. Band selection is simply based on the one that most closely resembles the occluso-gingival height of the tooth you are working on (see Figure 6). The contour of the band naturally follows the tooth shape and conforms to it, resulting in little or no flash when finished (see Figure 12).
The wedges are shaped to sit deeper due to their design and flexibility, sliding easily to seal the area completely (see Figure 13). The wedge should be placed from the widest embrasure, between the band and the adjacent tooth, creating the seal and contour needed for a smooth
finish.
The rings are Nickel Titanium (Nitinol) treated with plastic reinforcement, increasing their strength and resiliency (see Figure 14). They last much longer than other rings because they bounce back to their original shape. The shape of the ring is what helps the clinician reduce flash, saving time when finishing and polishing. These rings come in various sizes and can be used to restore multiple teeth at the same time by stacking the taller ring over the shorter ring in different areas concurrently. The wide ring is convenient when there is a portion of the cusp missing, allowing the clinician to contour easily without having to go through multiple steps.
That’s it. That’s all there is to it. Super easy and very rewarding. And the best part is that you can get the same results instantly by following this step-by-step process
